Collision Sentry, Collision Warning System, Forklift Collision Detection

Back to Product Category

Collision Sentry® Corner Pro

Making Noise in Collision Awareness

	Blind corner intersections are a prime spot for accidents in any industrial setting – accidents that can result in damage to equipment, the facility and most importantly to people. Collision Sentry Corner Pro works to prevent accidents at blind corners by sending both an audio and visual alert to warn of approaching traffic. Collision Sentry Corner Pro helps create a safer working environment in areas where forklift traffic and pedestrian traffic intersect.

		Collision Sentry Collision Pro
		Blind corners and intersections are a common hazard in most industrial settings. The Collision Sentry Corner Pro warning system helps lessen these hazards. The addition of the Collision Sentry Corner Pro system can: • Protect people from injury • Prevent equipment damage • Prevent damage to the facility • Increase and maintain productivity by avoiding delays due to accidents



	The Collision Sentry Corner Pro sends a warning ONLY when it senses movement in both detection zones; motion on both sides of the blind corner.

	Under those conditions, the Collision Sentry Corner Pro flashes in both directions and sounds an audible warning, providing enough time for corrective action.


Detection Zone		The Collision Sentry Advantage
		The Collision Sentry Advantage
		Audio Warning • Loud enough to be heard within the corner zone; pitch sets it apart from other background noise • Volume can be adjusted (high/low) or turned off • Sounds ONLY when motion is detected on both sides of the corner • Synchronized with light flash to reinforce warning Visual Warning • Flashes ONLY when motion is detected on both sides of the corner • LED lights angled; increasing light's intensity and optimizing visibility • Beam focused toward areas where it is best seen • Lens concentrates and increases beam’s intensity Simple Installation (see below for installation instructions) • Deploys immediately, portable, compact and lightweight • Integrated, recessed magnet mounts easily “snap on” to racking, maintaining a secure, tight fit. • Integrated mounting points for mounting the unit to non-magnetic surfaces • Optimal installation height is 7-9 feet on the upright Passive Infrared Motion Sensors • Detection zone 20-25" in each direction • Alert sent in ample time to take corrective action • Pre-set and ready to use Self-Powered • Standard D-cell batteries (included) • Blue light, beeping low battery indicator • Battery life depends on usage, but lasts a minimum of 12 months


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click the Model No. of the item you wish to purchase.

Collision Sentry Prices

Model No.	Description	Weight	Price
CLN-211	Warning System with Audio - Height of 7"	3 lbs	$240.15
CLN-211-CTN8	Pack of 8	24 lbs	$1,922.09

Installation Instructions

	Inspect your product for any visible signs of damage.


	To activate the Collision Sentry Corner Pro, pull out the plastic battery tab located inside the unit. Remove the door on the front of the unit, pull the tab and replace the door. This activates the three (3) “D” cell batteries that are included with each unit. The LED lights will begin blinking as the device becomes oriented to the environment. During this warm-up period, the blue low battery indicator also flashes. Note: Always activate the unit prior to installation. Pull the tab, close the door and the install the unit to the upright.


	The ideal placement for the unit is at a height between 7' and 9' (2-2.75 m). Install with the mounting tabs at the top.


	Use the integrated magnets on the back to "snap" the unit to a metallic corner or rack.


	The included nylon tether provides extra security when mounting the unit using the magnets. Using the tether is optional but recommended.


	Use the integrated mounting tabs to install the unit directly to nonmetallic surfaces.


	The product needs about 20 seconds to acclimate to the new environment and "learn" its new surroundings. During this warm-up, the warning lights will flash. The lights will go solid red for four seconds at the end of the warm-up period. This indicates the product is ready to use.


		Collision Sentry Corner Pro ships with the audio alarm activated and set to the highest volume. This alarm can be adjusted using the switches found inside the unit and located below the battery compartment. (See illustration). There are two switches used for adjusting the volume – a high/low switch and an off/on switch. 1. Remove the door on the front of the unit. 2. Alarm switches are located below the battery compartment. 3. Adjust the switches to the desired setting. 4. Reinstall battery door. 5. Unit is now ready for use.

Collision Sentry, Collision Warning System, Forklift Collision Detection, Forklift Collision Avoidance, Column Protectors,
Commercial Railing, Folding Gates, Guard Rails, Guardrail, Machine Guards, Rail, Protective Guards, Railing, and Traffic
Barricade from your source for material handling equipment.

Back to Product Category

Collision Sentry® Corner Pro