HEAVY DUTY STEEL FOLDING GATES PAIRS
				The Only Folding Security Gates Made With Heavy-Duty Galvanized Steel.
				They withstand brutal 4-season conditions like rain and snow. Our Gates stand up to harsh industrial chemicals and cleaners too.
				The Strongest Folding Security Gates on the Market. Our Security Gates are the only gates made with solid galvanized steel 5/8” self-securing drop pins designed to fit directly into floor holes. They provide maximum strength and maximum security. You cannot buy a stronger gate!
				They're Riveted Back to Back with Aircraft Quality Aluminum Rivets.
				They'll hold up to more stress, are rust resistant, they won't crack and the webbing won't separate.
Need Custom Security Gates? No Problem! No matter what your situation is, we can build a gate to your specs.
				Our Folding Security Gates pivot 180° on their Mountings — so they pivot completely out of the way, leaving the opening completely clear of obstructions.
						Pair Folding Security Gates are perfect for securing any kind of hall, entryway or window in any type of business or industry. Gates have open webbing that allows greater air circulation and visibility during the day, and tight security around the clock. They're perfect for lift-up doors, and larger doorways and hallways. Gates up to 24' wide are always in stock. Larger sizes are also available with quick turnaround. Pair Folding Security Gates are ideal for openings greater than 12'.
By providing more light and better air circulation you'll save on air conditioning costs. And the increased security folding gates provide means less theft and reduced loss prevention costs. And that means a healthier workplace, a safer school, and a more secure warehouse.
Our Pair Folding Security Gates are equipped with brackets, bearing washers and casters.
Pair Folding Security Gates can be installed virtually anywhere and any way you need them, including, inside door jambs, outside door jambs, between posts or bollards, attached to pallet racks, between walls and even in windows!
And they're easy to install. You can install our gates in less than 30 minutes!

PAIR FOLDING GATE INSTALLATION INSTRUCTIONS
About Our Heavy-Duty Folding Gates
• For installation on concrete floors. • Bottom of gate hinges on bearing washer and pin set into floor hole.    Do not remove bottom floor pin. • Top of gate hinges on "L" bracket bolted to wall or door frame. • To install gates inside overhead doors, bollards or to clear obstructions,    6" or 9" extension brackets are required. • Optional "H" Bracket joins each half of gate for added security.
									Step 3: Extend gate and hang "L" bracket on top of gate to verify where it will be mounted. To release tension you may lift the wheel 1/2"-3/4" off the floor. Mark and drill pilot holes into door frame or wall. It may be easier to drill pilot holes if you remove the gate from it's floor mount. Place bearing washer and bottom gate pin back into floor mount. Slip "L" bracket over top of gate and bolts (bolts not included.)
		Step 1: Before Installing decide on gate placement. "L" brackets that form top hinge allows gate placement in the recess of door frame. Installation can also be made outside or inside of wall next to door or opening frame. Either side of gate can be toward the outside of building. Put the "operating side" (the end with center drop pins) to the side used when padlocking the gate halves. A label on the operating side indicates RHT (right) or LFT (left) of a person facing the operating side.
									• Wood door frames or walls: 5/16" x 2"    lag bolts. • Steel door frames or walls: Drill and tap    for 5/16" x 2" lag bolts. • Brick or concrete frames or walls:    5/16" x    2" lag bolts set into 3/8" holes    with lead anchors.
		Extension brackets (order separately) clear overhead door tracks, bollards or obstructions. 6" brackets provide 4-3/4" clearance, 9" brackets provide 7-1/4" clearance.

		Step 2: Have a helper extend the gate and stand it upright where it will be mounted. CAUTION: Check to confirm gate will swing away from opening when not in use. This will provide a clear opening for normal traffic.					Step 4: Raise center drop pin and use attached notch to keep in place, this prevents damage to floor surface. Extend and retract gate to its stops to work out stiffness. Repeat steps 2-3 for other half of gate. CAUTION: Notice that center drop pin at this stage hits the other half of gate or rests on floor. Do not cut off drop pin. Step 5 addresses misalignment.
		• Drill 3/4" diameter x 3" deep hole, 1-1/4"    from wall into the floor for gate pin to    set into. • For 6" extension bracket drill 6" O.C.    from wall. • For 9" extension bracket drill 9" O.C.    From wall.
							Step 5: With center drop pin raised, extend both halves of gates together to center of opening, mark floor for center drop pin hole and drill a 3/4" diameter x 3" deep hole. Lower center drop pin (Note: some larger gates have an additional pin in the center of each web, mark and drill these last.) Secure gate halves with 1/2" shaft diameter padlock. Open gates slowly at first to avoid warping.
	Place a bearing washer over floor hole and set bottom gate pin into floor mount hole.
		Option: H bracket mounts overhead in center of gate. Extend both halves of gate together to center of opening. Position "H" bracket, mark and drill pilot holes into mounting surface. Attach "H" bracket with bolts (not included.)

Matching existing color schemes in your facility is a breeze
A galvanized steel finish is standard for Single, Pair, Door and Portable Gates. Yellow and black powder coating finish is standard for Barrier Gates. Custom powder coating is also available for all gates in over 300 DuPont colors.
			Galvanized Finish				Powder Coating Finish

PRICING FOR FOLDING GATES PAIRS
Part # Collapsed Height In Use Height Weight Price WIDTHS FROM 6' TO 8' PFG865 6' 6" 6' 96 $475.20 PFG870 7' 6' 6" 104 $518.40 PFG875 7' 6" 7' 110 $532.80 PFG880 8' 7' 6" 112 $561.60 PFG885 8' 6" 8' 130 $576.00  WIDTHS FROM 8' TO 10' PFG1065 6' 6" 6' 104 $504.00 PFG1070 7' 6' 6" 110 $532.80 PFG1075 7' 6" 7' 120 $561.60 PFG1080 8' 7' 6" 132 $590.40 PFG1085 8' 6" 8' 148 $619.20  WIDTHS FROM 10' TO 12' PFG1265 6' 6" 6' 112 $540.00 PFG1270 7' 6' 6" 116 $576.00 PFG1275 7' 6" 7' 122 $604.80 PFG1280 8' 7' 6" 152 $662.40 PFG1285 8' 6" 8' 158 $691.20 WIDTHS FROM 12' TO 14'  PFG1465 6' 6" 6' 128 $619.20 PFG1470 7' 6' 6" 138 $648.00 PFG1475 7' 6" 7' 140 $684.00 PFG1480 8' 7' 6" 164 $720.00 PFG1485 8' 6" 8' 174 $756.00 WIDTHS FROM 14' TO 16'  PFG1665 6' 6" 6' 140 $705.60 PFG1670 7' 6' 6" 164 $734.40 PFG1675 7' 6" 7' 166 $777.60 PFG1680 8' 7' 6" 180 $835.20 PFG1685 8' 6" 8' 196 $907.20 WIDTHS FROM 16' TO 18'   PFG1865 6' 6" 6' 160 $835.20 PFG1870 7' 6' 6" 170 $878.40 PFG1875 7' 6" 7' 180 $950.40 PFG1880 8' 7' 6" 186 $993.60 PFG1885 8' 6" 8' 190 $1,051.20   WIDTHS FROM 18' TO 20'  PFG2065 6' 6" 6' 178 $950.40 PFG2070 7' 6' 6" 180 $993.60 PFG2075 7' 6" 7' 185 $1,080.00 PFG2080 8' 7' 6" 192 $1,137.60 PFG2085 8' 6" 8' 197 $1,224.00   WIDTHS FROM 20' TO 22'  PFG2270 7' 6' 6" 210 $1,584.00 PFG2280 8' 7' 6" 220 $1,728.00   WIDTHS FROM 22' TO 24'  PFG2470 7' 6' 6" 230 $1,800.00 PFG2480 8' 7' 6" 240 $1,872.00
*UPS SHIPPABLE

Door Gate, Door Gates, Double Folding Gates, Double Gate, Double Gates, Expanding Gate, Folding Gate, Folding Gates, Folding Security Gates, Retractable Security Gates, Steel Folding Gate, and Steel Folding Gates from your complete source for material handling equipment.