Tapered Foam Seals, Foam Truck Dock Seals, Dock Seals

	T-1THD SERIES - 1000
	For door openings up to 8' wide x up to 8' high with inclined driveways

	Heavy Duty Tapered Foam Seals

		*Polyfoam Core*
*Construction*		*Polyfoam Core*
*Construction*		Insulating polyurethane foam conforms to the shape of the truck to form a tight weatherseal.
Bondor foam dock seals are con- structed of the finest materials and assembled to give you years of dep- endable service.

		*Full Width Header*
		Our header pad completely covers both sides to prevent rain from entering your dock area along the side pads.

*Single Layer Face*

*Mounting Board*
*Mounting Board*
Our foam core is bonded to a kiln- dried pressure treated 2" thick wood backboard for an easy, long-lasting installation.		*Color*
		Standard colors are black with a yellow guide stripe. Other colors available upon request.

*Closed Bottoms*
*Closed Bottoms*		*Tapered Side Pads*
Covered vents to allow air to escape during compression of the seal, reducing the amount of stress on the vinyl fabric.		*Tapered Side Pads*
		Tapered side pads accommodate an inclined driveway to your building. The specific taper is custom made to match the angle of your driveway.

*Rugged Vinyl Cover*
*Rugged Vinyl Cover*		*Galvanized Hardware*
A 40 oz. nylon reinforced vinyl material is used on our heavy duty seals. Top quality abrasion resistant 22 oz. vinyl coated nylon fabric is used to cover our standard seals.		*Galvanized Hardware*
		All Bondor Foam Seals are provided with appropriate galvanized mounting brackets. Building fasteners not included.


*Permanent Guide Stripe*
A 4" wide contrasting guide stripe is sewn on.




Top View

Square side pad cross section shown above


	Truck Bumpers Required

To order a series T-1THD Tapered Seal:

		Front View	Side View

1.	Determine (measure) your inclined driveway to establish the amount of driveway rise and your driveway length. See sketch below.

	"A" Note: In cases where the building wall is setback from the edge of the dock, the actual bumper projection required is less the building setback. Example: The incline chart indicates a 12" bumper "A" dimension but the building wall is setback 3", therefore the actual bumper necessary would be 9".

2.	Determine the requried dock bumper size and dock seal side pad dimensions by using the incline chart below. This chart is designed to leave the top of the truck approximately 6" from the building wall when the truck is fully docked.

	a. Find your driveway rise in the left column and follow across the chart to a driveway length closest to your actual measured length. Dimensions A, B & C are the recommended sizes of your dock bumpers and your dock seal taper. Dimensions B & C will be used in the price tables below to order the actual correct dock seal model #.

	b. Example: Driveway rise is 24", driveway length is 40'. At the intersection of these two rows in the chart, dimensions A = 12, B = 16 and C = 10. This means that for this example you would have dock bumpers (or a dock projection) of 12" with foam side pads which taper from 16" at the bottom to 10" at the top.

Driveway Length

10'

20'

30'

40'

50'

60'

70'

Rise"

2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52

9	14	12
10.5	16	12
12	16	10
14	18	10
16	20	10
17	22	12
19	23	10
21	25	10
23	27	10
25	29	10
27	31	10
29	33	10
31	35	10
33	37	10
35	39	10
36	40	10
38	42	10
40	44	10
42	46	10
44	48	10
46	50	10
48	52	10
50	54	10
52	56	10
54	58	10
55	59	10

9	14	14
9	14	12
9	14	12
10.5	16	12
12	16	12
12	16	10
12	16	10
14	18	10
15	20	12
16	20	10
16	20	10
17	22	12
18	22	10
19	23	10
20	24	10
21	25	10
22	26	10
23	27	10
24	28	10
25	29	10
26	30	10
27	31	10
28	32	10
29	33	10
30	34	10
31	35	10

9	14	14
9	14	14
9	14	12
9	14	12
10.5	16	14
10.5	16	12
10.5	16	12
12	16	12
12	16	10
12	16	10
13	18	12
14	18	10
14	18	10
15	20	12
16	20	10
16	20	10
17	22	12
17	22	12
18	22	10
19	23	10
19	23	10
20	24	10
21	25	10
21	25	10
22	26	10
22	26	10

9	14	14
9	14	14
9	14	14
9	14	12
9	14	12
9	14	12
9	14	12
10.5	16	12
10.5	16	12
10.5	16	12
12	16	12
12	16	10
12	16	10
12	16	10
13	18	12
14	18	10
14	18	10
15	20	12
15	20	12
16	20	10
16	20	10
16	20	10
17	22	12
17	22	12
18	22	10
18	22	10

9	14	14
9	14	14
9	14	14
9	14	12
9	14	12
9	14	12
9	14	12
9	14	12
9	14	12
10.5	16	12
10.5	16	12
10.5	16	12
12	16	12
12	16	12
12	16	10
12	16	10
12	16	10
13	18	12
13	18	12
14	18	10
14	18	10
14	18	10
15	20	12
15	20	12
16	20	10
16	20	10

9	14	14
9	14	14
9	14	14
9	14	14
9	14	12
9	14	12
9	14	12
9	14	12
9	14	12
9	14	12
9	14	12
10.5	16	12
10.5	16	12
10.5	16	12
10.5	16	12
12	16	12
12	16	12
12	16	10
12	16	10
12	16	10
12	16	10
13	18	12
13	18	11
14	18	10
14	18	10
14	18	10

9	14	14
9	14	14
9	14	14
9	14	14
9	14	14
9	14	12
9	14	12
9	14	12
9	14	12
9	14	12
9	14	12
9	14	12
9	14	10
10.5	16	12
10.5	16	12
10.5	16	12
10.5	16	12
12	16	12
12	16	12
12	16	12
12	16	10
12	16	10
12	16	10
12	16	10
13	18	12
13	18	12

Special Order Products - Contact Us		Use Standard T-1 Seal

3.	Select the desired model # from the price charts below by finding your B and C dimensions determined above such as: using the dimensions determined above (B dim. of 16 and C dim. of 10) for a door with a height of 8' and a width of 8' the model # for the standard heavy duty seal is T-1THD/P16/SQ-12/T1610/8WX8H.

4.	Add desired special options from below.

5.	*Remember to order 2 dock bumpers per seal from our bumpers section if they are not existing.*

6.	We invite you to let our engineers review your dock seal application. Complete the truck dock dimension sheet on our contact page and we will confirm your dock seal selection.


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click a Model No. of the item you wish to purchase.

Table A: T-1THD Series Pricing - Use tables B & C (shown below) for optional wear pleats

Bottom Side Pad Projection (Inches) B	Top Side Pad Projection (Inches) C	Recommended Dock Bumper	T-1THD Heavy Duty Tapered Dock Seal - add door width x door height to base Model # below	Price
14	12	9"-#B910-14	T-1THD/P14/SQ-12/T1412/--W X --H	$1,298
14	10	9"-#B910-14	T-1THD/P14/SQ-12/T1410/--W X --H	$1,298
16	14	10 1/2"-#B10510-14	T-1THD/P16/SQ-12/T1614/--W X --H	$1,408
16	12	10 1/2"-#B10510-14	T-1THD/P16/SQ-12/T1612/--W X --H	$1,408
16	10	10 1/2"-#B10510-14	T-1THD/P16/SQ-12/T1610/--W X --H	$1,408
18	16	12"-#B1210-14	T-1THD/P18/SQ-12/T1816/--W X --H	$1,519
18	14	12"-#B1210-14	T-1THD/P18/SQ-12/T1814/--W X --H	$1,519
18	12	12"-#B1210-14	T-1THD/P18/SQ-12/T1812/--W X --H	$1,519
18	10	12"-#B1210-14	T-1THD/P18/SQ-12/T1810/--W X --H	$1,519
B Dim.	C Dim.	Dock Bumper	Model #	Price
20	18	14"-contact us	T-1THD/P20/SQ-12/T2018/--W X --H	$1,627
20	16	14"-contact us	T-1THD/P20/SQ-12/T2016/--W X --H	$1,627
20	14	14"-contact us	T-1THD/P20/SQ-12/T2014/--W X --H	$1,627
20	12	14"-contact us	T-1THD/P20/SQ-12/T2012/--W X --H	$1,627
20	10	14"-contact us	T-1THD/P20/SQ-12/T2010/--W X --H	$1,627
22	20	16"-contact us	T-1THD/P22/SQ-12/T2220/--W X --H	$1,737
22	18	16"-contact us	T-1THD/P22/SQ-12/T2218/--W X --H	$1,737
22	16	16"-contact us	T-1THD/P22/SQ-12/T2216/--W X --H	$1,737
22	14	16"-contact us	T-1THD/P22/SQ-12/T2214/--W X --H	$1,737
22	12	16"-contact us	T-1THD/P22/SQ-12/T2212/--W X --H	$1,737
22	10	16"-contact us	T-1THD/P22/SQ-12/T2210/--W X --H	$1,737


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click a Model No. of the item you wish to purchase.


	Optional Wear Pleats/Surfaces (use charts below)

		40 oz. wear pleat surfaces for the full length of the side pads provide maximum wear and abrasion resistance. Available in 4" or 8" exposure.

		NOTE: Each seal ordered with wear pleats includes pleats on head pad.

8" pleat exposure shown
			8" pleat exposure shown here	4" pleat exposure shown here

Table B: T-1THD Series Pricing with Optional Wear Pleat Surface - 8" exposure

Bottom Side Pad Projection (Inches) B	Top Side Pad Projection (Inches) C	Recommended Dock Bumper	T-1THD Heavy Duty Tapered Dock Seal with Optional Wear Pleat Surface 8" Exposure - add door width x door height to base Model # below	Price with 8" Exposure Pleat
14	12	9"-#B910-14	T-1THD/P14/SQ-12/T1412/WP8/--W X --H	$1,642
14	10	9"-#B910-14	T-1THD/P14/SQ-12/T1410/WP8/--W X --H	$1,642
16	14	10 1/2"-#B10510-14	T-1THD/P16/SQ-12/T1614/WP8/--W X --H	$1,751
16	12	10 1/2"-#B10510-14	T-1THD/P16/SQ-12/T1612/WP8/--W X --H	$1,751
16	10	10 1/2"-#B10510-14	T-1THD/P16/SQ-12/T1610/WP8/--W X --H	$1,751
18	16	12"-#B1210-14	T-1THD/P18/SQ-12/T1816/WP8/--W X --H	$1,859
18	14	12"-#B1210-14	T-1THD/P18/SQ-12/T1814/WP8/--W X --H	$1,859
18	12	12"-#B1210-14	T-1THD/P18/SQ-12/T1812/WP8/--W X --H	$1,859
18	10	12"-#B1210-14	T-1THD/P18/SQ-12/T1810/WP8/--W X --H	$1,859
B Dim.	C Dim.	Dock Bumper	Model #	Price
20	18	14"-contact us	T-1THD/P20/SQ-12/T2018/WP8/--W X --H	$1,969
20	16	14"-contact us	T-1THD/P20/SQ-12/T2016/WP8/--W X --H	$1,969
20	14	14"-contact us	T-1THD/P20/SQ-12/T2014/WP8/--W X --H	$1,969
20	12	14"-contact us	T-1THD/P20/SQ-12/T2012/WP8/--W X --H	$1,969
20	10	14"-contact us	T-1THD/P20/SQ-12/T2010/WP8/--W X --H	$1,969
22	20	16"-contact us	T-1THD/P22/SQ-12/T2220/WP8/--W X --H	$2,081
22	18	16"-contact us	T-1THD/P22/SQ-12/T2218/WP8/--W X --H	$2,081
22	16	16"-contact us	T-1THD/P22/SQ-12/T2216/WP8/--W X --H	$2,081
22	14	16"-contact us	T-1THD/P22/SQ-12/T2214/WP8/--W X --H	$2,081
22	12	16"-contact us	T-1THD/P22/SQ-12/T2212/WP8/--W X --H	$2,081
22	10	16"-contact us	T-1THD/P22/SQ-12/T2210/WP8/--W X --H	$2,081


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click a Model No. of the item you wish to purchase.

Table C: T-1THD Series Pricing with Optional Wear Pleat Surface - 4" exposure

Bottom Side Pad Projection (Inches) B	Top Side Pad Projection (Inches) C	Recommended Dock Bumper	T-1THD Heavy Duty Tapered Dock Seal with Optional Wear Pleat Surface 4" Exposure - add door width x door height to base Model # below	Price with 4" Exposure Pleat
14	12	9"-#B910-14	T-1THD/P14/SQ-12/T1412/WP4/--W X --H	$1,834
14	10	9"-#B910-14	T-1THD/P14/SQ-12/T1410/WP4/--W X --H	$1,834
16	14	10 1/2"-#B10510-14	T-1THD/P16/SQ-12/T1614/WP4/--W X --H	$1,942
16	12	10 1/2"-#B10510-14	T-1THD/P16/SQ-12/T1612/WP4/--W X --H	$1,942
16	10	10 1/2"-#B10510-14	T-1THD/P16/SQ-12/T1610/WP4/--W X --H	$1,942
18	16	12"-#B1210-14	T-1THD/P18/SQ-12/T1816/WP4/--W X --H	$2,052
18	14	12"-#B1210-14	T-1THD/P18/SQ-12/T1814/WP4/--W X --H	$2,052
18	12	12"-#B1210-14	T-1THD/P18/SQ-12/T1812/WP4/--W X --H	$2,052
18	10	12"-#B1210-14	T-1THD/P18/SQ-12/T1810/WP4/--W X --H	$2,052
B Dim.	C Dim.	Dock Bumper	Model #	Price
20	18	14"-contact us	T-1THD/P20/SQ-12/T2018/WP4/--W X --H	$2,162
20	16	14"-contact us	T-1THD/P20/SQ-12/T2016/WP4/--W X --H	$2,162
20	14	14"-contact us	T-1THD/P20/SQ-12/T2014/WP4/--W X --H	$2,162
20	12	14"-contact us	T-1THD/P20/SQ-12/T2012/WP4/--W X --H	$2,162
20	10	14"-contact us	T-1THD/P20/SQ-12/T2010/WP4/--W X --H	$2,162
22	20	16"-contact us	T-1THD/P22/SQ-12/T2220/WP4/--W X --H	$2,270
22	18	16"-contact us	T-1THD/P22/SQ-12/T2218/WP4/--W X --H	$2,270
22	16	16"-contact us	T-1THD/P22/SQ-12/T2216/WP4/--W X --H	$2,270
22	14	16"-contact us	T-1THD/P22/SQ-12/T2214/WP4/--W X --H	$2,270
22	12	16"-contact us	T-1THD/P22/SQ-12/T2212/WP4/--W X --H	$2,270
22	10	16"-contact us	T-1THD/P22/SQ-12/T2210/WP4/--W X --H	$2,270

SPECIAL OPTIONS:

To order any of the special options add the model # suffix desired to the base model # selected from the
T-1THD Series Dock Seal charts above. Example: T-1THD/P16/SQ-12/T1610/8WX8H-WFHP18

Weighted Valance Curtain reduces top
gap when low trucks are frequently docked
- curtain hangs between side pads.

Model Number Suffix	Drop	Price
-VC15	15" drop	$149
-VC30	30" drop	$209

Wide Face Header Pad (wider than STD 12")
- For docks which service a broader range of
truck heights.

Model No. Suffix	Header Pad Face Width	Price
-WFHP14	14"	$198
-WFHP16	16"	$214
WFHP18	18"	$225

ARCHITECTURAL SPECIFICATIONS - Model T-1THD Heavy Duty Tapered Foam Seal

Truck Dock Seals

Truck dock seals shall be heavy duty tapered as manufactured by the Bondor Division of FS Industries,
W. Greenwich, RI, to fit a door opening of 8' wide x 8' high.

Construction

Pads to have a polyurethane foam core bonded to a 2" x 12" kiln dried pressure treated wood backboard to give
a finished projection of ______________. Side pads to be 8' - 0" long (standard). Side pads to have 4" wide
contrasting guide stripe sewn on. Bottom of pads to have 3" upward taper to prevent pinching between truck and
bumpers. Bottom of pads to be closed with covered side vents to allow air during compression and to prevent
condensation.

Cover Material

Pads to be wrapped with 40 oz. vinyl coated nylon.

Foam Drape Seals, Bondor, Wear Pleats, Heavy Duty, Dock Door Loading Seal, Dock Door Seals, Foam Truck Dock Seals, Dock Seals, Loading Dock Door Seals, and Loading Dock Seals from your source for material handling equipment.

T-1THD SERIES - 1000

Heavy Duty Tapered Foam Seals

Foam Drape Seals, Bondor, Wear Pleats, Heavy Duty, Dock Door Loading Seal, Dock Door Seals, Foam Truck Dock Seals, Dock Seals, Loading Dock Door Seals, and Loading Dock Seals from your source for material handling equipment.